通过认证
“深圳中性优质灰白硅酮耐候结构胶（793A）/300ml”参数说明
| 类型： | 密封胶 | 型号： | 793A |
| 规格： | 300毫升 | 商标： | 美氏 |
| 包装： | 25支 | 颜色： | 定制 |
| 容量： | 300毫升 | 产量： | 100000 |
“深圳中性优质灰白硅酮耐候结构胶（793A）/300ml”详细介绍
“美氏793A”耐候硅酮密封胶是一种中性固化的密封胶：1）不腐蚀基材；2）固化收缩率低；3）在低温（-45°C）至高温（＋150°C）内保持一致弹性；4）柔软抗震，耐变形；5）适合于玻璃，铝材，石材，混凝土，砖瓦，陶瓷，塑料间的非结构性粘结密封。
说明：
1）施工温度在5℃~40℃之间；
2）用两块布法清洁基材；
3）将胶嘴按需要的大小做45°切断；
4）将胶打满接缝处
5）约25分钟结皮。
重要：
1）使用前请做材料相容性测试；
2）不用于结构性装配或表面温度（45°C）以上的材料；
3）不用于渗出油污或溶剂的材料。
注意：
远离儿童！
避免接触眼睛和皮肤！
如有接触，请用水冲洗；仍然不适的请就医检查。
执行标准：GB/T14683-2003
保质期：7个月（“MEISHI793A” Weather proofing silicone sealant is a neutral cure silicone sealant:1)Not corrosion to the materials;2)Low shrinkage on curing;3)Keep elastic in low(-45℃) and high(+150℃) temperatures; 4)High grade soft,be able to bear oscillation; 5)Suitable for glass,aluminum material,stone,concrete,brick,ceramic,plastic,non-structural sealing.
DIRECTIONS:
1)Construcation applycabie between 5℃~40℃;
2)Substrates should be solvent cleaned using two clothes method;
3)Cut the nozzle to desired opening at 45°angle ;
4)Fill the joint completely;
5)Formation of skin in 25 minutes.
IMPORTANT:
1)Please do material compatibility testing before use；
2)Do not use in structural applications or where surface temperatures exceed 45℃ for materialsafety;
3)Incompatible oozing out oily or solvents.
PRECAUTIONS:
Keep out of the reach of children!
Avoid contact with eyes and skin!
In case of contact,flush with lot water;If still indisposed,consult a doctor.
STANDARS: GB/T14683-2003.
DURABILITY: 9Months(
说明：
1）施工温度在5℃~40℃之间；
2）用两块布法清洁基材；
3）将胶嘴按需要的大小做45°切断；
4）将胶打满接缝处
5）约25分钟结皮。
重要：
1）使用前请做材料相容性测试；
2）不用于结构性装配或表面温度（45°C）以上的材料；
3）不用于渗出油污或溶剂的材料。
注意：
远离儿童！
避免接触眼睛和皮肤！
如有接触，请用水冲洗；仍然不适的请就医检查。
执行标准：GB/T14683-2003
保质期：7个月（“MEISHI793A” Weather proofing silicone sealant is a neutral cure silicone sealant:1)Not corrosion to the materials;2)Low shrinkage on curing;3)Keep elastic in low(-45℃) and high(+150℃) temperatures; 4)High grade soft,be able to bear oscillation; 5)Suitable for glass,aluminum material,stone,concrete,brick,ceramic,plastic,non-structural sealing.
DIRECTIONS:
1)Construcation applycabie between 5℃~40℃;
2)Substrates should be solvent cleaned using two clothes method;
3)Cut the nozzle to desired opening at 45°angle ;
4)Fill the joint completely;
5)Formation of skin in 25 minutes.
IMPORTANT:
1)Please do material compatibility testing before use；
2)Do not use in structural applications or where surface temperatures exceed 45℃ for materialsafety;
3)Incompatible oozing out oily or solvents.
PRECAUTIONS:
Keep out of the reach of children!
Avoid contact with eyes and skin!
In case of contact,flush with lot water;If still indisposed,consult a doctor.
STANDARS: GB/T14683-2003.
DURABILITY: 9Months(
“深圳中性优质灰白硅酮耐候结构胶（793A）/300ml”其他说明
| 用量估算表 | |||||||
| 厚度 | 宽 度 | ||||||
| 6 | 9 | 15 | 18 | 21 | |||
| 6 | 8.3 | 4.1 | 3.3 | 2.8 | 2.4 | ||
| 9 | 5.5 | 2.8 | 2.2 | 1.8 | 1.6 | ||
| 12 | 4.1 | 2.1 | 1.7 | 1.4 | 1.2 | ||
